Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Pocket
Gate repair in Pocket comes down to one thing most of the time: the post under the gate, not the hinge on top of it. Our Gate Repair team works on Pocket’s oversized driveway gates every week, and the pattern is consistent. Clay soil heaves, posts kick out, wide swing gates drop and scrape. Glenn Pacheco built Gatehouse Gate Repair to focus on gates and nothing else, so when a Pocket homeowner calls us about a sagging gate, we know to check the footing before we touch a hinge. Call (833) 620-5971 and we’ll be out to diagnose it.
Why Gatehouse Gate Repair Is Pocket’s Preferred Gate Repair Company
Pocket homeowners keep calling us back because we treat a sagging gate as a structural problem, not a hardware swap. Most gate companies in Sacramento replace hinges, charge the call-out, and leave. Six months later the gate drags again because the real issue was a post set too shallow in expansive clay. We re-foot, re-square, and re-hang so the repair holds through the next rainy season. That’s why our reputation in Pocket has grown on word of mouth along Havenside Drive, Riverglen Way, and the side streets off Pocket Road.
Pocket’s housing stock is mid-century ranch homes on generous lots, which means long driveways and wide gate spans you don’t see in newer south-city subdivisions. Our techs know these gates. A 14-foot wood swing gate on a 1970s hinge post behaves differently than a 6-foot ornamental gate in Land Park. We work on both, but around here the work is dominated by post-and-span corrections, not decorative repair.
When you call about a stuck gate or one that won’t close, we get to Pocket quickly because our techs dispatch from Sacramento and know the neighborhood’s streets, not just the freeway exits. You won’t wait on a generalist who has to Google your zip code.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Driveway Gate Repair in Pocket
Driveway Gate Repair on Pocket’s large lots usually means a long, wide swing gate has started dragging or binding. The panel itself is often fine. What’s failed is what’s under it: a hinge post that heaved out of the clay, or a column that’s leaning because roots from mature trees have shifted the soil. We pull the post, set a deeper footing, then re-hang and re-square the panel so the latch lands clean and the operator stops fighting the load.
A typical driveway gate repair in Pocket runs $350 to $850 depending on how far the post has moved and whether the operator needs re-tuning after the panel is realigned. If the post is sound and only hinges have worn, you’re looking at $180 to $400. We quote the full price before any work starts, so the number you approve is the number you pay.
Post Reset and Re-Hang
This is the bread-and-butter repair in Pocket. We dig out the old post, check how deep it was actually set, and install a new or salvaged post with a deeper concrete footing. Then we re-hang the gate on fresh hinges and adjust the latch side so the panel sits square in the opening.
If the panel is oversized, we may add a mid-span support or anti-sag hardware so it doesn’t start pulling again after the next wet winter.
Gate Realignment and Latch Adjustment
When a Pocket gate won’t latch in summer, it’s usually the heat. Wood frames warp on large privacy gates, and the latch or rack and pinion drift out of alignment. We plane, shim, and re-set the catch so it engages cleanly without you lifting or kneeing the gate shut.
If an opener is involved, we always re-check the limit settings after realignment so the motor isn’t over-traveling against a stop it can’t reach.
Gate Welding in Pocket
Gate Welding in Pocket is most common on older chain-link and steel tube gates that have cracked at stress points, especially where the frame meets the hinge or where a center stile carries the load. A gate that’s been sagging for years eventually fatigues the metal, and welding is the only repair that lasts. Glenn’s team welds on-site when possible, and we grind and rust-treat every weld so it doesn’t become the next failure point.
Expect $250 to $700 for most Pocket welding jobs depending on the number and location of the cracks. A single hinge crack might run $250 to $350. A cracked frame on a wide driveway gate with multiple stress fractures usually lands in the $500 to $700 range. Every weld is quoted before we strike an arc, and we’ll tell you honestly if the gate is too far gone to weld safely.
Cracked Frame and Hinge Repair
The most common weld repair we do in Pocket is at the hinge plate, where years of a sagging gate have focused all the stress onto one point. We weld the crack, reinforce the plate if needed, and then address the alignment so the repaired gate doesn’t crack again in the same spot.
Weld and Rust Restoration
Sacramento’s wet winters and the irrigation overspray common on large lots mean steel gates in Pocket rust faster than you’d think. We cut out rusted sections, weld in new steel, and coat the repair. This is also the time to catch thin spots before they become holes.
Trusted Brands We Service in Pocket
If your Pocket driveway has an automatic gate, odds are the operator is a LiftMaster, FAAC, BFT, or Linear. We work on all four, plus the wider set of gate automation brands we carry parts for. Because we’re a gate-only shop, our techs diagnose these systems daily rather than occasionally. That means we don’t guess and swap parts until something works. We identify the fault, quote the repair, and get it done. For Pocket customers with long driveways where running mains power is impractical, we also service solar-ready LiftMaster and FAAC setups and can wire a system to run off a properly sized solar array with battery backup.
Common Gate Repair Problems We See in Pocket Homes
- Post-winter drag and scrape. Pocket’s clay soil swells and heaves after the rainy season. Hinge posts that weren’t footed deep enough kick out, and the gate drops far enough to drag the driveway. This is the number one call we run in late winter and early spring.
- Summer warp on wide wood gates. A 12- or 14-foot wood privacy gate on a big lot soaks up Central Valley heat and warps. The latch stops landing, the panel binds on the latch post, and the operator strains against the extra friction. We come out when the gate is hot to fix it in its worst state.
- Leaning posts under mature canopies. Many Pocket homes have 50-year-old fence lines under mature trees. The posts lean as roots and soil moisture shift, and the gate settles with them. A hinge swap won’t fix a leaning post. We reset it.
- Operator and limit failures on heavy gates. When a wide, heavy gate sags even a little, the opener’s limit switches get out of whack. The motor over-travels, the gate slams against the stop, and parts wear fast. We re-square the gate first, then re-tune the operator.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Pocket, CA
Here’s what Pocket homeowners can expect to pay for common gate repairs with Gatehouse Gate Repair:
- Minor hinge replacement or latch adjustment: $180 to $400
- Post reset and re-hang on a single swing gate: $350 to $850
- Gate welding (single crack or stress point): $250 to $350
- Gate welding (multiple cracks or frame reinforcement): $500 to $700
- Operator diagnosis and limit re-tuning: $150 to $400, parts quoted separately if needed
What affects the price in Pocket is usually the width of the gate and what’s under the post. Wide gates on long driveways cost more to re-hang because they require more labor and often a second person to muscle the panel safely. The quote we give you before starting is the price you pay. We don’t adjust invoices after the fact. Call (833) 620-5971 for a free estimate on your specific gate.
We Also Serve Cities Near Pocket
Our gate repair routes cover Pocket and the surrounding South Sacramento neighborhoods. If you’re in Greenhaven, Meadowview, Valley Hi, or Oak Park, the same dedicated gate techs from Gatehouse Gate Repair can reach you quickly and apply the same footing-and-span knowledge we use every day in Pocket. Same specialist focus, the full nine-brand parts coverage, and the same honest quote-before-work policy.
Serving Pocket, CA – Our Local Coverage Area
We’re based in the Pocket area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Pocket
Because the clay soil under your gate posts expands when it absorbs winter rain, which heaves the post out of the ground just enough that a wide gate drops several inches and starts scraping. The fix is not another hinge swap; it’s pulling the post, digging a deeper footing, and re-hanging the panel square. On a generous lot off Havenside Drive, we had exactly this call after the winter rains: a wide wood swing gate had dropped and was scraping the concrete. Our tech pulled the old hinge post, found it set shallow in the expanding clay, and reset it with a deeper footing before re-squaring and re-hanging the oversized panel. The owner had already paid once for a hinge swap that didn’t hold. Call (833) 620-5971 and we’ll quote the real fix.
Yes, we regularly set up solar-powered gate operators for Pocket homeowners whose driveway entrance sits far from the house electrical panel. LiftMaster and FAAC both make solar-ready operators that work reliably in Sacramento’s sun, and we’ve installed and serviced enough of them to know the battery sizing and panel orientation for our climate. We don’t sell you a solar setup unless it’s the right call for your specific gate width and weight.
Yes, wide and heavy gates are most of what we fix in Pocket. Gates in the 12- to 16-foot range on mid-century ranch lots are the norm here, not the exception. We’re set up to handle the dead weight, the long spans, and the post loads these gates create. Most of the time the fix starts under the gate, not on top of it. Call (833) 620-5971 for an estimate on a wide gate.
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We’re brand-agnostic, which means we recommend whatever part or repair fits your existing system, not whatever brand we happen to sell. That’s a real advantage for Pocket homeowners whose gates were installed years ago under a brand a generalist wouldn’t stock parts for.
Yes. Every automatic gate opener must have working entrapment protection, including safety edges, photoelectric sensors, or both, depending on the gate type and installation age. This is both a code requirement and a genuine safety concern: a 500-pound gate closing against a child or pet is a serious hazard. If your Pocket gate’s safety devices aren’t working, that’s a repair we’ll quote directly and honestly. Don’t bypass them to keep a gate working. Call (833) 620-5971 and we’ll get it right.
Call Gatehouse Gate Repair Today
If your Pocket gate is dragging, stuck open, stuck closed, or just won’t behave, call (833) 620-5971. Glenn Pacheco and the Gatehouse team know Pocket’s gates, Pocket’s clay soil, and Pocket’s long driveway spans better than any generalist ever will. We quote the full price before work starts, we fix the actual problem, and we stand behind the repair.
Written by Glenn Pacheco, Owner at Gatehouse Gate Repair, serving Pocket and South Sacramento.